ISOMAG-MS2500
The "flanged" sensor MS 2500, for universal use, is suitable for all applications and flow ranges; available with the widest range of diameters.
Body material: Carbon Steel and AISI304 / 316 Stainless Steel.
Nominal diameters: from DN 25 to DN 2000.
Flow rate: 0 ÷ 113.000 m3 / h.
Nominal pressure: from PN 6 to PN 250.
Process connections: Flanges according to all international standards.
Liquid temperature: -20 ÷ 180 ° C.
ISOMAG-MS501
The "microflow" sensor MS 501 is the smallest instrument in the series, with a wide range of applicability thanks to the variety of its attachments.
Body material: AISI304 / 316 stainless steel.
Nominal diameters: from DN 3 to DN 20.
Flow rate: 0 ÷ 12.500 l / h.
Nominal pressure: PN 16 or PN 40.
Large selection of process attacks.
Liquid temperature: -20 ÷ 150 ° C.
Lining material: PTFE.
Large selection of electrode materials.
ISOMAG-CS8100
Body material: NORYL + 30% Fiberglass.
Nominal diameters:.
Flow rate: 50 ÷ 2,400 l / h.
Nominal pressure: 1000kPa.
Process connections: GAS M or NPT.
Liquid temperature: -20 ÷ 85 ° C.
Coating material:.
ISOMAG-MS3780
The insertion sensor MS 3780 is used for mounting in depressurized lines and with diameters from 80 to 2,000 mm. It is ideal for line monitoring and for HVAC applications.
Sensor material: AISI316 stainless steel.
Nominal pressure: from PN 16 to PN 64.
Process connections: Threaded or flanged.
Liquid temperature: from -20 to + 100 ° C.
Coating material: PEEK.
Electrode material: Hastelloy C276.
ISOMAG-MS3810
The insertion sensor MS 3810 is used for mounting on pressurized lines with diameters from 80 to 8000 mm. It is ideal for temporary measurement campaigns, line monitoring and leak detection.
Sensor material: 316 Stainless Steel.
Wide choice of sensor lengths for installation in pipes of different diameters.
Nominal pressure: PN 25.
Process connections: Threaded 1 "Ball valve for extraction under load.
Liquid temperature: from 0 to 100 ° C.
Coating material: PEEK.
Electrode material: AISI316L.
Possibility of integrating pressure measurement.
Accuracy: ± 2% of the value read.
ISOMAG-MS3820
The CS3820 is an electromagnetic insertion flowmeter is a battery-powered compact flowmeter, available in different lengths suitable for mounting in pressure pipes with diameters from 80 to 8000 mm. It is designed for temporary measurement campaigns, for monitoring and detection of leaks, or for permanent installation in sites where power supply is not available. Isoil Industria offers a wide choice of lengths for installation in pipes of different diameters as well as the possibility of mounting an autonomous pressure sensor.
ISOMAG-MV110
The MV110 Converter is mainly used in the water market, in HVAC and in industrial applications where performance and outputs or basic protocols are required. Accuracy: ± 0.8% of the read value (± 0.4% of the optional read value). Repeatability: ± 0.2% Programming via keyboard on the front or via PC with mini USB adapter Available outputs: 3 digital, max 2 analog, one of which Hart, Modbus communication Flexible mounting to view the display on the other Housing material: Nylon loaded with 15% fiberglass or Aluminum Protection IP 67 (on request IP68) Available functions: low flow cut, bidirectional measurement, peak cut, empty pipe, alarm limit etc. Available accessories: rechargeable backup battery (guarantees measurement in the absence of power), 4 GB data logger, BIV self-check function of the sensor's electrical characteristics. Can be coupled to the flanged or wafer sensors of the Isomag® line.
ISOMAG-MV145
The MV145 part of the FLOWIZ family is a battery-powered converter for flow meters that can power any Isomag sensor, insertion or flanged up to DN1800. The MV255 is also able to manage up to two pressure or temperature sensors. The MV145 can be powered by lithium or alkaline batteries, the batteries can be easily replaced, without interrupting the measurement. Batteries have an estimated life of 15 years or more based on measurement conditions. Optionally the MV145, can be powered from the mains, c.a. or c.c. or from a solar panel via the DC connection; in this case the batteries have a backup function, avoiding data loss in the event of a power failure.
ISOMAG-MV255
The MV255 part of the FLOWIZ family is a battery converter with integrated modem that can power any sensor of the Isomag family, insertion or flanged up to DN1800. The MV255 is also able to manage up to two pressure or temperature sensors. The MV255 FLOWIZ ™ has an integral 3G UTMS / GPRS modem that allows wireless transmission of all measured flow and pressure / temperature data. Data security in communication is guaranteed by encryption with the TSL / SLL standard, the data is packaged to reduce the time and costs of data transmission, SMS alarms can be sent in cases where the process thresholds are exceeded. The MV255 can be powered by lithium or alkaline batteries, the batteries can be easily replaced, without interrupting the measurement. Batteries have an estimated life of 15 years or more based on measurement conditions. Optionally the MV255 can be powered from the mains, a.c. or c.c. or from a solar panel via the DC connection; in this case the batteries have a backup function, avoiding data loss in the event of a power failure.
ISOMAG-MV800
Ultra-compact blind converter suitable for coupling with ISOMAG® full-passage sensors up to DN300. Can be used for flow measurements on liquids with a minimum conductivity of 20 µS / cm. Measurement accuracy +/- 0.8% of the measured value. Die-cast aluminum housing, with IP 67 protection degree. Power supply 18-30 V DC, electrical connections via 5-pole connector Programming from PC via dedicated software Particularly suitable for applications in environments with a high degree of humidity or where no local indication of the flow rate value.
ISOMAG-ML4-F1
The ML4F1 converter is specific for fast "filling" applications (frequency up to 400 Hz).
Accuracy: ± 0.2% of the value read.
Repeatability: better than 0.1%.
Programming via PC.
Galvanic separation: all inputs and outputs are separated from each other and from the power supply.
Housing material: AISI304 stainless steel.
Programmable functions: low flow cut, bidirectional, double field, peak cut, empty pipe, alarm limit, dosage with automatic preset etc.
Can be coupled to all Isomag sensors up to DN 1000 except for insertion ones, MS 4000 and CIAO.
ELECTROMAGNETIC BATTERY FLOW METER
Battery-powered RBmag meters do not require external power, therefore they are a valid alternative to
conventional mechanical measuring systems and in isolated applications without power supply.
ELECTROMAGNETIC FLOW METER
The product line is suitable for multiple applications in the "industrial process" area. In addition to various coating materials, electrodes in hastelloy c, tantalum and titanium are also available. The converter is available with the most diffuse communication interfaces such as Modbus, Hart and through an application for Android smartphones via bluetooth. It has integrated the data logger on board for recording measurements over time. The measured quantities are stored in a TXT file compatible with Excel or other equivalent software. The data logger is physically made up of a USB pen drive. The USB port of the pen drive is located behind the removable O-LED display.
ELECTROMAGNETIC FLOW METER FOR SANITARY PROCESS
This line is aimed at applications in the food and pharmaceutical sector. Connections type DIN 11851 or CLAMP DIN
32676 make it possible to use it in sectors such as dairy, breweries and others. The construction is completely
made of stainless steel and PFA coatings are available for the pharmaceutical sector.
MID001 CERTIFIED ELECTROMAGNETIC FLOW METER
This product line is suitable for multiple applications in the "industrial process" field. The MID certification according to the 2014/32 / EU directive, and compliant with the OIML49 R - EN14154 - ISO4064 regulations, makes it suitable for all fiscal uses. In addition to various coating materials, electrodes in hastelloy c, tantalum and titanium are also available. The converter is available with the most common communication interfaces such as Modbus.
ELECTROMAGNETIC FLOW METER U0D0
New range of electromagnetic flow meters with sensor tubes in plastic material (ABS) which, thanks to the particular internal geometry, are less influenced by the proximity of disturbing elements such as fittings, curves etc. and can therefore be installed at "ZERO DIAMETERS". The electronic converter, with a large and bright removable O-LED display, features a data logger on a USB pen-drive. The transmission of the flow measurement is possible via the analog, pulse and MODBUS RTU outputs. Any alarm signals are made by means of no. 2 programmable relays. The meter is suitable for use with a wide range of conductive liquids, also chemically aggressive, thanks to the possibility of selecting the most suitable electrode material for the application.
BATTERY ELECTROMAGNETIC FLOW METER U0D0
Battery-powered meters do not require external power supply, therefore they are a valid alternative to conventional mechanical measuring systems and in isolated applications without power supply.
Thanks to the particular internal geometry, it is less influenced by the proximity of disturbing elements such as fittings, curves etc. and can therefore be installed at "ZERO DIAMETERS". The meter is suitable for use with a wide range of conductive liquids, also chemically aggressive, thanks to the possibility of selecting the most suitable electrode material for the application.
ELECTROMAGNETIC FLOW METER FOR SMALL DIAMETERS
Meter suitable for measuring flow values from a minimum of 0.04l / m (DN5) up to a maximum of 100l / m (DN15). The body entirely in AISI 316L makes it an instrument suitable also for chemical / food applications. The small size and the multiplicity of varieties of the threaded connections allow an easy and quick mechanical installation. Rotation of the TFT display allows for horizontal or vertical mounting orientation.